Theses and Dissertations (Electronic Engineering)

Permanent URI for this collection

https://hdl.handle.net/10352/187

Browse

Browsing Theses and Dissertations (Electronic Engineering) by Author "Janse van Rensburg, J. F."

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Design and development of a 200 W converter for phosphoric acid fuel cells
    (2013-03) Kuyula, Christian Kinsala; Janse van Rensburg, J. F.
    “If we think oil is a problem now, just wait 20 years. It’ll be a nightmare.” — Jeremy Rifkin, Foundation of Economic Trends, Washington, D.C., August 2003. This statement harmonises with the reality that human civilisation faces today. As a result, humankind has been forced to look for alternatives to fossil fuels. Among possible solutions, fuel cell (FC) technology has received a lot of attention because of its potential to generate clean energy. Fuel cells have the advantage that they can be used in remote telecommunication sites with no grid connectivity as the majority of telecommunication equipment operates from a DC voltage supply. Power plants based on phosphoric acid fuel cell (PAFC) have been installed worldwide supplying urban areas, shopping centres and medical facilities with electricity, heat and hot water. Although these are facts regarding large scale power plants for on-site use, portable units have been explored as well. Like any other fuel cell, the PAFC output power is highly unregulated leading to a drastic drop in the output voltage with changing load value. Therefore, various DC–DC converter topologies with a wide range of input voltages can be used to regulate the fuel cell voltage to a required DC load. An interleaved synchronous buck converter intended for efficiently stepping down the energy generated by a PAFC was designed and developed. The design is based on the National Semiconductor LM5119 IC. A LM5119 evaluation board was redesigned to meet the requirements for the application. The measurements were performed and it was found that the converter achieved the expectations. The results showed that the converter efficiently stepped down a wide range of input voltages (22 to 46 V) to a regulated 13.8 V while achieving a 93 percent efficiency. The conclusions reached and recommendations for future research are presented.
  • Thumbnail Image
    Item
    Design and development of an automated temperature controller for curing ovens
    (2012-08-30) Schoeman, Ruaan Mornè; Janse van Rensburg, J. F.
    Curing of materials in order to obtain different properties has been a practice for many years. New developments in composite materials increase the need to control certain variables during the curing process. One very significant variable is temperature. Temperature control by itself is an old practice, however when the need for repeatedly controlling the process accurately over long periods of time arises, a system is required that outperforms normal manual control. One of the aspects within such a system that needs to be considered is the ability to replicate the temperatures within an oven which were originally used for a specific material’s curing profile. This means that a curing profile would need to be defined, saved for later and finally be interpreted correctly by the controlling system. Different control methods were simulated to enable the system to control the temperature which has been defined by literature. This dissertation introduces a variation on the standard control methods and shows improved results. Switching the oven on and off in order to increase or decrease internal oven temperature seems simple, but can cause switching devices to decrease their operational life span, if not designed carefully. A combination switch was introduced which harnesses the advantages of two very common switching devices to form an improved combination switch. Software for the personal computer environment, as well as software for the embedded environment were developed and formed a control system that produced acceptable results for temperature control. Accuracies of 98% and more were achieved and found to be acceptable according to standard engineering control practices. An accurate temperature profile controller was designed, simulated and built in order to control the temperature inside a specific curing oven which, in turn, determined the curing properties of specific materials. The overall results were satisfactory which lead to achieving the objectives outlined in this dissertation.
  • Thumbnail Image
    Item
    Development of a universal bidirectional galvanic isolated switch module for power converter applications
    (2013-06) Mokhalodi, Kopano; Janse van Rensburg, J. F.
    The global trends towards energy efficiency have facilitated the need for technological advancements in the design and control of power electronic converters for energy processing. The proposed design is intended to make the practical implementation of converters easier. The development of a universal bidirectional galvanic isolated switch module will be used to drive any MOSFET or IGBT in any position in any topology whether the load is AC or DC. Semiconductor switches are required and are also integrated for fast switching times in power converter applications The structure of the power switch module consists of an opto-coupler which will provide an isolation barrier for maximum galvanic isolation between the control circuitry and power stage. It also consists of a high performance gate drive circuit for high speed switching applications with a floating supply.